Technical and Product Support
Accessing the Web Site
In-depth printable service manuals and other documentation are available for
download from the RadiSys Web site:
http://www.radisys.com
Then click on
Service and Support
to access a link to the
documentation, drivers, and BIOS. Documentation is available at
this Web site in Adobe
®
Acrobat
®
.PDF format and may be viewed
and printed using Acrobat
®
Reader
™
software. BIOS files are
available as self-extracting disk image files. Links are provided to
various partners’ web sites where any files and tools needed to
install drivers are available for download.
Calling Technical Support
RadiSys Corporation provides technical support Monday–Friday,
8:00 a.m.–5:00 p.m. Central Time in the continental USA and
8:30 a.m.–5:00 p.m. in Europe.
To expedite your request, have the RadiSys product model and
serial number available. Then call one of the following numbers:
•
Inside the continental USA, dial (800) 627-8700.
•
Outside the continental USA, dial (713) 541-8200 (add long
distance/international codes).
•
In Europe, dial +31-36-5365595.
Inspection of Contents / Packaging of Product
The packaging for this product has been tested to assure that it will
withstand responsible handling by the carrier.
Caution:
Inspect contents immediately and file a claim with the
carrier for any damage. Save the shipping box and packaging
material to use for any further shipment of this equipment.
However, if the packaging is damaged and is not suitable for
shipment, call RadiSys Technical Support to obtain new packaging.
The warranty may be void if the product is returned using
unapproved or damaged original packaging.
Returning Your Product
A Returned Material Authorization (RMA) number must be written
on the outside of the shipping carton of all equipment returned to
RadiSys for service and/or repair. It is recommended that any
correspondence included with the carton contents also refer to the
RMA number.
Note:
The factory will refuse the shipment if it is sent freight collect
or if it does not display an RMA number.
Quick Start
To begin operating your EPC-2322 single-board computer, perform
the following:
1. Ensure that the jumper settings match your requirements
2. Ensure that all switch settings match your requirements.
3. Install the SBC onto a passive backplane in a chassis.
4. Attach all necessary peripheral devices to the appropriate
headers and connectors on the SBC.
5. Power on the system.
6. Run the Setup Utility if you need to change any settings to
match your requirements.
Note:
See the table “Setup Utility” for factory default settings.
To avoid damage or injury, always exercise the following
precautions when handling the equipment:
• Use a grounding wrist strap or other static-dissipating device
• Power off the system
• Disconnect all power cords
!
Jumper Settings
2-Pin Jumpers
JP1
JP6
JP7
JP13
Serial 2 Configuration
None
1—2
None
None
RS-232 (default)
1—2
None
1—2
1—2
RS-422
JP18
3.3V On-Board Power Supply
None
Enabled
1—2
Disabled
3-Pin Jumpers
JP4
JP5
I/O Model
1—2
1—2
SP Model
2—3
2—3
MKP Model
Switch Settings
SW1-1
Not Used
SW1-2
On-Board ROM Access
Open/Off
Flash Memory enabled (default)
Closed/On
Crisis Recovery Mode enabled
SW1-3
CMOS RAM
Open/Off
Normal operation (default)
Closed/On
Factory default values are loaded
Setup Utility
Setup Item
Default Setting
System Time
Current (Hours, Minutes, Seconds)
System Date
Current (Month, Day, Year)
Diskette A
1.44/1.25 MB 3½”
Diskette B
Disabled
IDE Adapter Type
Auto (all 4 possible drives)
Memory Cache
Enabled
Cache System BIOS Area
Write Protect
Cache Video BIOS Area
Write Protect
Cache Base 0 — 512K
Write Back
Cache Base 512 — 640K
Write Back
Cache Extended Memory Area
Write Back
Cache C800 — EFFF
Disabled (all regions)
Boot Summary Screen
Enabled
Floppy Check
Disabled
Quiet Boot (Graphics)
Enabled
POST Errors
Enabled
Keyboard Numlock
Auto
Key Click
Disabled
Keyboard Auto-Repeat Rate
30/sec
Keyboard Auto-Repeat Delay
1/2 sec
Serial Port A
3F8, IRQ4
Setup Utility (continued)
Setup Item
Default Setting
Serial Port B
2F8, IRQ3
Parallel Port
Bi-Directional, 378, IRQ7
Floppy Disk: Base I/O Address
Enabled, Primary
Local Bus IDE Adapter
Enabled
Adaptec Ultra-2 SCSI Adapter
Disabled
ECC Config
ECC
Enable Memory Gap
Disabled
Alias ISA 512 — 528 MB
Disabled
DMA Aliasing
Enabled
16-Bit I/O Recovery
4.5
8-Bit I/O Recovery
4.5
ISA Bus Speed
PCI Clock ÷ 4
Watchdog Timer Status
Disabled
Watchdog Timer Delay
1.2 sec
ISA Bus GAT
Disabled
PCI Delayed Transactions
Enabled
PCI IRQ Line 1 — 4
Auto Select (all IRQ lines)
USB IRQ Enable
Yes
Latency Timer
Auto
Cache Line Size
Auto
ISA Graphics Device Installed
No
PCI/PNP ISA UMB Region Exclusion
Available (All regions)
PCI/PNP ISA IRQ Resource Exclusion Available (All IRQ’s)
System Alarm Temperature (°C)
60
CPU Alarm Temperature (°C)
110
Thermal Duty Cycle
37.5%
PS/2 Mouse
Auto Detect
Onboard Speaker
Enabled
Use Multiprocessor Specification
1.1
CPU BIOS Update
Enabled
Plug & Play O/S
No
Secured Setup Configuration
Yes
Reset Configuration Data
No
Large Disk Access Mode
DOS
Password on Boot
Disabled
Fixed Disk Boot Sector
Normal
Diskette Access
Supervisor
Virus Check Reminder
Disabled
System Backup Reminder
Disabled
Power Savings
Disabled
Standby Timeout
Off
Auto Suspend Timeout
Off
Hard Disk Timeout
Disabled
Video Timeout
Disabled
Resume on Modem Ring
Off
Resume on Time
Off
Resume Time
00:00:00 (24-hour format)
Console Redirect Port
Disabled
Console Redirect Baud Rate
9600
StockCheck.com
