manualshive.com logo in svg

RadiSys C1XTN02, Service Manual

Share
Download
RadiSys C1XTN02 Service Manual Download Page 54

Chapter 3: Technical Data

Service Manual

43

Watchdog Timer

Overview

The watchdog timer provides an escape from a system lockup caused by electrical noise, 
electrostatic discharge, processor lock-up, etc. The watchdog provides the escape by 
performing a reset of all system components.

Reset

Once the watchdog timer detects an activity pulse, an internal timer begins to count down from 
the preset time delay, either 150 milliseconds or 1.2 seconds. If the watchdog counts down to 
zero before it detects another pulse, it will perform a reset. This, in turn, issues a reset to the 
PCI and ISA buses, thereby resetting the devices installed on the buses.

Control

Two features control the watchdog timer operations: Status and Delay. These options are 
defined in the Setup Utility. See 

page 25

.

•

Watchdog Status: sets the source of the activity monitored by the watchdog timer.

•

Enabled: the source of the pulse is the CPU Address Strobe (ADS) line.

•

Disabled: the source of the pulse is the CPU system clock.

•

Watchdog Delay: sets the amount of time in which the system will be monitored for 
activity, either 150 milliseconds or 1.2 seconds.

User Mode

In addition to the Setup Utility features, there is a User mode to control the watchdog timer 
operations. A user-controlled bit can be used to block the activity pulse from the watchdog 
timer. If the control bit is set, the user-defined application must clear the bit within the 
designated time to prevent a reset.

For more information, contact Technical Support. See 

Customer Support

 on 

page vi

.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for C1XTN02





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands