RadioLink Ei168RC Instruction Manual Download Page 6 | Manualshive

Page: 6 / 28

background image

2. Quick Install Guide

The Ei168RC RadioLINK Base must be installed by a qualified electrician.
The maximum number of RadioLINK Alarms in each system is 12.

Install each RadioLINK Base in the centre of the
ceiling at least 0.30m from light fittings as per
the Smoke/Heat Alarm instructions and connect
to nearest mains circuit.

Slide Alarm on to the Ei168RC RadioLINK Base.
This will automatically activate the rechargeable
back-up cells in the base.

Repeat this procedure for all Alarms in the
system.

6

«
...
4
5
6
7
8
...
»

Summary of Contents for Ei168RC





























Reviews:

No comments

Related manuals for Ei168RC

Brand: Paradox Pages: 72

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 32

Brand: Olympus Pages: 374

Brand: Olympus Pages: 66

Brand: Vectaire Pages: 2

Brand: Samsung Pages: 2

Brand: Hanwha Vision Pages: 20

Brand: Ansel Pages: 84

EasyLook PPDF17000

Brand: Abus Pages: 23

Brand: GST Pages: 11

Brand: IC Realtime Pages: 11

Brand: Bogen Pages: 4

Brand: Dahua Pages: 35

Brand: Beta Three Pages: 11

Inspire SBS 560

Brand: Creative Pages: 1

AXE 320 PULSE smart

Brand: Alfain Pages: 13

Brand: Vitek Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands