background image

 
Do not listen at extremely high volume levels.  Extended, high-volume  
listening can lead to permanent hearing loss.  Follow these guidelines to 
protect your hearing, especially when you use headphones. 
 
    Always start by setting the volume to the lowest level possible before 
    you begin listening.  Put the headphones on, then gradually increase 
    the volume as necessary. 
 
    Once you set the volume, do not increase it.  Over a period of time,  
    your ears adapt to the volume level, so a volume level that does not  
    cause discomfort might still damage your hearing. 
 
USING THE SLEEP TIMER 
 
You can set the radio to play for up to 1 hour and 59 minutes and then  
automatically turn off so you can fall asleep as you listen. 
 
Follow these steps to set the sleep timer for a playing time of 59 minutes 
or less. 
 
1.  Set RADIO ON/OFF to OFF to turn off the radio. 
 
2.  Press and hold down SLEEP. 
 
3.  While holding down SLEEP, repeatedly press (or press and hold) MINUTE 
    until the display shows the desired minute setting. 
 
4.  Release SLEEP. 
 
Follow these steps to set the sleep timer for a playing time of 1 hour or 
more. 
 
1.  Set RADIO ON/OFF to OFF to turn off the radio. 
 
2.  Press and hold down SLEEP. 
 
    NOTE:  Each time you press sleep, the sleep timer resets to 0:59. 
 
3.  While holding down SLEEP, press and release HOUR.  The display shows 
    1:59. 
 
4.  While continuing to hold down SLEEP, repeatedly press (or press and  
    hold) MINUTE until the display shows the desired minutes setting. 
 
5.  Release SLEEP. 

Summary of Contents for Chronomatic-300

















Reviews: