3
2. Insert the tip of a pen or pencil into the clear cover’s notch, lift up
the cover’s edge, then remove the cover.
3. Run the cable through the strain relief slot on the bottom of the
control.
4. Loosen the three terminal screws, then connect the silver-colored
wire to Terminal 1, the center wire (copper) to Terminal 2, and the
third wire (copper) to Terminal 3.
5. Recheck the wiring order, then tighten all three terminal screws.
6. Replace the clear cover.
Caution: Be sure there are no loose strands of wire that could short
between the terminals.
Synchronizing and Testing
Follow these steps to synchronize and test the antenna rotator.
1. After you wire the drive motor and the control, plug the control’s
power cord into a standard AC outlet (120 volts, 60 Hz).
2. Turn the control's dial fully clockwise. You can hear the control’s
motor running as the red dot on the control’s dial slowly moves
clockwise and the top of the drive motor turns. When the rotator
reaches the end of rotation, the top of the drive motor stops turn-
ing, the control’s motor turns off, and the dot stops moving.
Note: Depending on the original setting of the drive motor, it might
stop turning before the control motor turns off. If this happens,
wait for the control’s red dot to stop moving before you proceed to
Step 3.
3. Turn the control’s dial fully counterclockwise. When the control’s
motor turns off and the dot stops moving, the control and the drive
motor are synchronized. Setting the control’s dial to
N
(north)
should align the two arrows on the side of the drive motor — one
on the side of the base and one on the side of the rotating top.
Note: If the arrows do not align, try Steps 2 and 3 again. If the
drive motor’s arrows still do not align when you set the control’s
dial to
N
, take the antenna rotator to your local RadioShack store
for assistance.
4. Disconnect the rotator cable from the control so that you can
mount the drive motor.
Preparing the Antenna Mast
To install the antenna rotator, you need two separate masts — a sup-
port mast for the drive motor and an antenna mast for the antenna it-
self. The support mast can be whatever length is appropriate (see
“Mounting the Drive Motor”). However, before you mount the antenna,
cut the antenna mast using the following guidelines. If the antenna is:
• up to 5 feet long, the mast length should not exceed 5 feet
• between 5 and 8 feet long, the mast length should not exceed 3
feet
• over 8 feet long, the mast length should not exceed 2 feet
• over 8 feet long with braces, cut the antenna mast 12 inches
below the point where you attach the braces to the mast
If you mount two antennas to the mast, the mast length should not ex-
ceed 4 feet. Mount the small antenna on top of the mast and the larger
antenna 12 inches from the bottom of the mast.
Mounting the Drive Motor
You can mount the drive motor on a support mast 1
1
/
8
to 1
3
/
4
inches in
diameter. If the mast is over 5 feet long, we recommend that you use
guy wires to secure the mast.
Warning: Select a mounting location where the antenna cannot come
in contact with power lines while you install it, and where the installa-
tion cannot fall across power lines if a guy wire should fail.
Use the supplied hardware to mount the drive motor on a support
mast.
1. Thread a plain nut over the unslot-
ted end of one of the studs until it is
about 1 inch from the unslotted
end. Screw the stud’s unslotted
end as far as it will go into one of
the drive motor housing’s holes.
Firmly tighten the nut against the
housing to secure the stud.
Repeat this step with each of the
other three studs.
2. One of the supplied clamps is
longer than the other three. Slide
this longer clamp over the lower
pair of studs and one of the other
clamps over the upper pair of studs. Then, with the toothed side
facing the housing, thread a lock nut onto each stud. Leave the
clamps loose so you can easily slide the mast behind the clamps.
3. Slide the drive motor onto the support mast until the drive motor’s
protrusion rests on top of the mast.
4. Use a
7
/
16
-inch wrench to tighten the lock nuts.
Caution: Overtightening can deform and weaken the mast.
5. If you use guy wires to secure the mast, guide the wires through
the lower clamp’s two outer holes.
Mounting the Antenna
Follow these steps to mount the antenna.
1. Insert the two U-bolts into the
holes in the top portion of the
drive motor, as shown. Slide a
clamp over the ends of each U-
bolt.
2. With the toothed side facing the
housing, thread a lock nut onto
each
U-bolt
end.
Leave
the
clamps loose so you can easily
insert the mast.
3. Slide the antenna mast behind
the clamps, then rotate the mast
until the antenna points north.
Tighten the lock nuts.
Caution: Overtightening can deform and weaken the mast.
Note: When most stations are south of your antenna, point the
antenna south. If you do this, remember that the antenna points in
the opposite direction from that indicated on the control. Use
Guy Wire
Plain
Nut
Stud
Clamp
Lock
Nut
Protrusion
Support
Mast
U-Bolt
Clamp
Lock
Nut
Antenna
Mast
