Radio Shack 12-251 Owner'S Manual Download | Manualshive

Page: 16 / 36

background image

16

PROGRAMMING THE
WEATHERADIO

Your Weatheradio is preprogrammed to receive
broadcasts for all FIPS codes, and is prepro-
grammed with the seven national NOAA broadcast
frequencies (Channels 1–7).

The first time you use your Weatheradio, it is auto-
matically set to use the NOAA weather broadcast
frequency 162.400 MHz (Channel 1) and receive all
SAME alert signals broadcast within a 50-mile radi-
us of where you installed it.

Depending on your location, you might need to se-
lect a different channel and enter one or two FIPS
codes into the Weatheradio.

Notes:

• To stop programming the Weatheradio at any

time during the steps described in this section,
set

PROGRAM/OPERATE

to

OPERATE

. The

Weatheradio saves any valid entries you made.

• The Weatheradio will not receive a weather

alert while you program it.

12-251.fm Page 16 Tuesday, March 14, 2000 12:40 PM

«
...
14
15
16
17
18
...
»

Summary of Contents for 12-251





































Reviews:

No comments

Related manuals for 12-251

Brand: Bush Pages: 9

Brand: E.F. Johnson Company Pages: 127

Brand: Harbor Freight Tools Pages: 11

Brand: Alcatel Pages: 102

Brand: Sangean Pages: 41

Brand: GME Pages: 36

Brand: Cobra Pages: 35

Brand: WEATHER DIRECT Pages: 24

Brand: LOGICOM Pages: 100

Brand: Trevi Pages: 48

Brand: Wintec Pages: 13

Brand: Vertex Standard Pages: 6

Brand: Vertex Standard Pages: 10

Brand: Vertex Standard Pages: 20

Brand: Vertex Standard Pages: 31

Brand: Vertex Standard Pages: 66

Brand: Midland Pages: 16

Brand: Midland Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands