background image

www.radialeng.com

THREE YEAR TRANSFERABLE LIMITED WARRANTY

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free 
from defects in material and workmanship and will remedy any such de-
fects free of charge according to the terms of this warranty. Radial will 
repair or replace (at its option) any defective component(s) of this product 
(excluding fi nish and wear and tear on components under normal use) for 
a period of three (3) years from the original date of purchase. In the event 
that a particular product is no longer available, Radial reserves the right 
to replace the product with a similar product of equal or greater value. In 
the unlikely event that a defect is uncovered, please call 604-942-1001 
or email [email protected] to obtain an RA number (Return Autho-
rization number) before the 3 year warranty period expires. The product 
must be returned prepaid in the original shipping container (or equivalent) 
to Radial or to an authorized Radial repair center and you must assume 
the risk of loss or damage. A copy of the original invoice showing date of 
purchase and the dealer name must accompany any request for work to 
be performed under this limited and transferable warranty. This warranty 
shall not apply if the product has been damaged due to abuse, misuse, 
misapplication, accident or as a result of service or modifi cation by any 
other than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE 
ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES 
WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMIT-
ED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE 
RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE 
YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY 
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS 
ARISING FROM THE USE OF THIS PRODUCT.  THIS WARRANTY 
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE 
OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU 
LIVE AND WHERE THE PRODUCT WAS PURCHASED.

Radial

®

 PreComp

 User Guide - Part# R870 1253 00 • rev.1

Specifi cations and appearance are subject to change without notice.

Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam BC  V3C 5M5
tel:  604-942-1001 • fax:  604-942-1010 
[email protected] • www.radialeng.com

!

  This product is intended for professional use only. 

The user should be familiar and experienced with 
the 500 series rack and module format.

Summary of Contents for PreComp 500 series













Reviews: