manualshive.com logo in svg

RADEMACHER 3500 30 74, Translation Of The Original Installation And Commissioning Manual, Page: 28 / 32

Share
Download
RADEMACHER 3500 30 74 Translation Of The Original Installation And Commissioning Manual Download Page 28

28

EN

i

12.  Error messages and troubleshooting

Errors that have occurred are shown on the display with an 

error code.

E1 = The drive is not installed

 

◆

Install the DuoFern Radiator Actuator 2 at a suitable place.

E2 = Error in the mechanics

An error has been detected during the installation run.

 

◆

Repeat the installation run.

E3 = Installation run too short

 

◆

Check the installation position of the DuoFern Radiator 

Actuator 2.

 

◆

Adjust the installation with an adapter if necessary.

 

◆

Replace a defective device.

E4 = Error in the DuoFern network

The logged-on HomePilot

®

 is no longer accessible via radio.

 

◆

Ensure that there is no disruptive radio source nearby. 

 

◆

Ensure that the DuoFern Radiator Actuator 2 is in 

the radio range of the HomePilot

® 

or DuoFern Room 

Thermostat 2.

i

 

Information about E1 - E3

 

You can start a new installation run by reinserting 

the batteries, see page 10.

Summary of Contents for 3500 30 74

































Reviews:

No comments