background image

2

How SoundAlert Works

SoundAlert is the Talking Wireless

Detection System that tells you

where and when someone’s been

detected.

The Sensor/Transmitters can be

located indoors or outdoors and

when movement is detected, they

send a signal to the Base Station.

The SA12 system consists of a Base

Station, plus 2 Sensor/ Transmitters

and the SA24 System has 2 Base

Stations and 4 Sensor /Transmitters.

Additional Base Stations and

Sensor/ Transmitters can be 

purchased separately.

The Sensor/Transmitters are 

battery operated and they transmit

radio signals to the Base station.

The Base Station has six pre-

recorded messages, or you can

easily record your own messages.

The Base Station also has 4 “C”

relay dry contact outputs to activate

other devices, such as X10,

Leviton, or Lutron controls.

3

Specifications

Base Station

• 6 separate voice messages of 6 

seconds each. Use pre-recorded 

voice messages or record your own.

See page 6.

• Receives signals from an unlimited 

number of Sensor/Transmitters

• Speaker Volume Control 
• Voice Message Test Buttons:

One button per zone

• 4  “C” relays trigger X-10 or Leviton   

DHC devices

• Missed Message Indicator:

Flashing LED

• Missed Message Playback:

Push Button

• FCC Approved
• Low Battery LED indicates that a 

Sensor/Transmitter has a low battery

• Low Battery voice message identifies

specific zone with low battery

• AC/DC Power Adapter - 

6’ cord length

• Power Requirement: 120V AC 60Hz

• Power Transformer 9VDC 1 AMP

• Installation: Wall or tabletop

Sensor / Transmitter

• Detection range: 40’ x 40’

Adjustable sensor patterns (see

page 9)

• Adjustable (rotating, pivoting) 

mounting

• Indoor/Outdoor weatherproof 

construction

• Time Adjustment 0-3 minutes

(factory set to 1 minute)

• Battery operated (9V battery 

included)

• FCC approved
• Transmission distance: up to

1000’ in open space 300’

through walls

• Operating Temperature: 14ºF to

122ºF (-10ºC to 50ºC)

Contents

Deluxe System SA24:

2 Base Stations

4 Sensor / Transmitters

Basic System SA12:

1 Base Station

2 Sensor / Transmitters

SA12

Basic

System

Shown

Base Station

Sensor/Transmitters

3

SA Manuel.indd   3

4/29/05   3:06:45 PM

Summary of Contents for Sound Alert

















Reviews: