manualshive.com logo in svg

R3 ECHORING ER--EB 1000M, User Manual, Page: 11 / 15

Share
Download
R3 ECHORING ER--EB 1000M User Manual Download Page 11

http://echoring.com
Revision: 1.2

5 Web­based Configuration Interface

5.1 General Information

The Web­based configuration interface is used for configuring, deploying and reconfiguring

devices.

5.2 Set up and access Web User Interface

1. Arrange and connect a PC, the R3 Configuration Server and the EchoRing Ethernet

Bridges, intended to be in the same network or sub­network, to the switch, according
to Figure 5­I:

Figure 5­I: Configuration set­up

2. Power on to the R3 Configuration Server and network switch.

3. Open the PC’s network settings and configure the static IP address 172.30.1.10 and

the subnet mask 255.255.0.0.

4. Open a web browser and enter the URL

http://172.30.0.1

.

ATTENTION

— The web­based user interface is designed for the web browsers Firefox (version 60

or newer) and Chrome (version 64 or newer). Other browsers may not support full functionality.

!

5.3 Configure the Device

ATTENTION

— New devices require a software update before use. Please see Section 5.5

!

1. Set up and access the Web User Interface (see Section 5.2).

© by R3 – Reliable Real­time Radio

Page 7 of 11

5. Web­based Configuration Interface

Summary of Contents for ECHORING ER--EB 1000M
















Reviews:

No comments