TEX150
25 / 40
User Manual
Rev. 4.0 - 27/07/01
8.2.7 Frequency selector card replacement
•
Open the top and bottom covers of the unit.
• Unscrew the four fixing screws of the front panel.
• Disconnect connector CN1 situated on the Contraves card.
• Unscrew the two card's fixing screws on the front panel.
• Remove the Contraves card.
8.2.8 PLL card replacement
•
Open the top and bottom covers of the unit.
• Disconnect connectors CN1, J2, and J5, desolder the two wires connected on
J1 and J3 of the PLL Card.
• Unscrew the fixing screws of the PLL card metal box on the internal chassis.
• Remove the metal box.
NOTE:
For any adjustment is sufficient remove the top and bottom covers of the
metal box.
8.2.9 Mono/MPX card replacement
•
Open the top and bottom covers of the unit.
• Disconnect connectors JP1, JP2 and JP3.
• Unscrew the four nuts fixing the card on internal chassis.
• Unscrew the screw inside the INPUT LEVEL knob and slide it off.
• Raise the card from its supports, simultaneously sliding the switches and the
INPUT LEVEL switch pivot from the panel.
8.2.10 Alarms card replacement
•
Open the top and bottom covers of the unit.
• Disconnect connectors JP1 and JP2 of the Stereo Coder card (or Mono/MPX
card) to ease the removal of the Alarms card.
• Disconnect connectors CN1, CN2, CN3 and CN4.
• Unscrew the fixing screws of the card on the internal chassis.
• Remove the card.
NOTE:
During replacement of broken devices it's necessary to pay attention to
device's pin position and insertion, to check that the device's fixing screws aren't
in short-circuit and to check that the soldering is good and without impurities.
Interpose between devices and heat-sink an electronic silicone compound.
Summary of Contents for TEX150
