background image

XR-OP-EN 

- 9 -

MACHINE COMPONENTS

1. 

STROBE LIGHT (OPTIONAL):  

Optional Strobe Light silently alerts others nearby of the machines 

presence 

2. 

RECOVERY TANK LID:  

 Latch must be secured for Recovery Tank to seal properly

3. 

ADJUSTABLE SEAT WITH ARM RESTS:  

The machine is equipped with an ergonomic seat with 

adjustable arm rests and positioning

4. STEERING 

WHEEL: 

 

Steers the main Drive Wheel

 

5. 

SEAT ADJUSTMENT:  

Permits the Seat to be adjusted forward and backward for operator comfort 

6. HEADLIGHT: 

 

Helps you see in low light areas and to warn oncoming traffi c

7. 

POLYURETHANE ROLLERS:  

Helps prevent damage to machine and objects you may drive near

8. 

SIDE BROOMS (OPTIONAL):  

Optional Side Brooms allow for debris clean up directly up to walls 

9. 

FRONT DRIVE TIRE:  

Drives and steers the machine

10.  TIE DOWN POINTS:  

Location for tie down straps during transport

11. SIDE 

WIPERS: 

 

Controls water on turns by directing it to the Squeegee

12.  ONBOARD CHARGER (OPTIONAL):  

Two optional placements for the Onboard Charger Option 

which allows the operator to charge machine by plugging machine directly into any standard wall 
outlet

13. REAR 

WHEELS: 

 

Cut for complete water control

14.  SQUEEGEE ROLLERS:  

Helps protect the Squeegee

15.  TANK LATCHES:  

Permits access to the Recovery Tank

16.  SOLUTION SIGHT GAUGE & DRAIN HOSE:  

Shows precise level of cleaning solution in Tank while 

also used as a Solution Tank drain hose

17.  RECOVERY DRAIN HOSE:  

Allows for controlled draining of the Recovery Tank

18.  SPRAY JET HOSE (OPTIONAL):  

Optional Spray Jet hose allows operator to utilize the Solution 

Tanks cleaning solution in areas where the machine may not reach to scrub

19.  REAR BUMPER:  

Offers squeegee system protection from damage

20.  SQUEEGEE BLADE:  

Squeegees water to be recovered by the vacuum hose

21.  ONBOARD SUDS SYSTEM (OPTIONAL):  

SUDs system allows the operator to precisely add soap 

directly to the Scrubdeck

1

2

3

4

5

6

7

8

9

10

11

13

12

14

10

16

17

18

15

21

19

20

Summary of Contents for XR 34'' DISK











































Reviews: