background image

 

Pa

ge

 

 

 

Brand

 

Compatible vehicles

 

infotainment systems

 

Vauxhall 

Astra K (Sports Tourer) 2016 >

 

Insignia A  2014-2016 

Insignia B  2017 > 

Mokka X 2016>

 

Navi 900 intelliLink with 8inch 

touch monitor (Gen. 1 und 2)

 

 

 

Limitations 

 

Video only

 

The interface inserts ONLY video signals into the infotainment. For 

inserting Audio signals either the possibly existing factory audio-

AUX-input or a FM-modulator can be used. If 2 audio sources shall 

be connected to the infotainment, an additional electronic is 

necessary to switch them. 

 

Factory rear-view camera 

Automatically switching-back from inserted video to factory rear-

view camera is only possible while the reverse gear is engaged. To 

delay the switch-back an additional electronic part is required. 

 

Guide lines 

If the CAN-box does not receive the required information from the 

vehicle CAN-bus, the guide-lines will not be supported.  

 

 

 

1.2.

 

Checking the compatibility of vehicle and accessories 

 

Compatibility 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for 27-590




















Reviews: