background image

Revison: 1.0 

     Date: 12 /01/2010

Tel: 800-677-5264 | Fax: 888-526-4329

Installation

Page 5 of 6

R. Lang Company

Tel 800-677-5264 | Fax 888-526-4329

Tel 800-677-5264 | Fax 888-526-4329

R. Lang Company

Install Astragal Stops

Install  Astragal  Stops  (#R6490/R6495)  into  head  and  sill  track.  

Fasten  using one (1) #6 x 3/4” 

flat head screw through hole and 

into track.  The astragal blocks are keyed on the bottom to fit in 

the screw groove in the track, and the stop upright will point at the 

active door. Make sure stops are evenly placed, top and bottom, 

and hold stationary door in required position.  The stop upright 

should  be  placed  at  that  position  in  the  track.   The  active  door 

Step 7

Adjust Strike

Follow the instructions in Step 6, Page 3 for adjustment of the strike if necessary. 

Installation Complete 

Make sure all components are properly installed.  Check the overall operation of the door.  Drawbar guides should move freely over 

both the bottom and top tracks and connect squarely with the closer.  If properly installed, the door will want to return to the housing 

quickly after breaking contact with the strike.

should easily open and close, latching at the inactive door when required.  If more depth for the astragal pins are desired, a 7/32” drill 

bit can be used to drill through the astragal stops into the track. Be careful here, that this process does not compromise the integrity of 

the building structure or weather barrier. R. Lang Company will not be responsible for any damage as a result of improper application 

of this process.

Step 8

R6490 (RH)

R6495 (LH)

Astragal Block 

Location

Drawbar with 

Astragal Pin.

(Pin is in

slot in drawbar)

Roll-Away®  LIMITED WARRANTY   

To the original purchaser, R. Lang Company warrants this product and its components parts to be free of defects on materials and workmanship for a period 

of one year from the date of purchase.

Damage caused by accident, improper installation or abuse, is specifically excluded from this warranty. Manufacturer’s liability on any claim shall not 

exceed the cost of the product. In no instance shall manufacturer be responsible for consequential damage from the use of this product, including damage 

to existing door during installation or operation.

For a period of one (1) year from the date of purchase, any defective product or part may be sent, freight prepaid, to R. Lang Company, 8240 West Doe 

Avenue, Visalia, California (93291) for replacement or repair at no charge. Proof of purchase date and a pre-approved Return Materials Authorization must 

accompany any returned item. For further information about this warranty, write to Consumer Affairs Manager at R. Lang Company.  

This warranty replaces any and all previous warranties, either written, oral, or implied, and is the only warranty made on this product by the R. Lang 

Company. This warranty gives you specific legal rights.  Rights may vary from state to state. 

Active Door

Stop upright

Summary of Contents for Roll Away R6500 Series







Reviews: