manualshive.com logo in svg

R. Beck Maschinenbau Ergoplan EP1 FH, Operating Manual

Share
Download
R. Beck Maschinenbau Ergoplan EP1 FH Operating Manual Download Page 24

 

24 

BA_BM_ERGOPLAN-1-2-3_EN_46-21.docx

 

 

13

 

Maintenance and Repair 

Maintenance and repair work may only be carried out by competent, trained and instructed personnel. If neces-
sary, further operating instructions and/or additional documents must be observed. 

 

 

 

After maintenance or repair work on the work and assembly table,  
always carry out a function test. 

 

•

 

Wear safety shoes with steel-toed caps.  

•

 

Wear suitable protective clothing. 

 

 

Repair work on mechanical and hydraulic components may only be carried out by authorised 
and trained personnel. 

 

 

Before any maintenance and repair work is carried out, chapter 

 4 "Safety" must be read 

carefully and observed. 

13.1

 

Maintenance Intervals

 

Interval  Action 

Daily 

Check all components for damage and have them replaced by competent personnel if neces-
sary. If you have any questions, please contact our support (phone: 0049 7576 / 962 978 - 0). 

Monthly 

Lubricate the castors and bearings a little. 

Annual 

a)

 

 Make and document annual inspection of the Ergoplan according to regulations. 

b)

 

 Treat the work bench top with linseed oil and remove glue residues. 

14

 

Decommissioning

 

•

 

Before taking out of service, the platform of the Ergoplan must be lowered completely. 

•

 

For recommissioning, observe chapter 

 9 

“

Installation and commissioning 

“.

 

•

 

For the final scrapping of the Ergoplan, please refer to chapter 

 15. 

 

 

Summary of Contents for Ergoplan EP1 FH




























Reviews:

No comments

Brands by name

Popular brands

Load more brands