Quonset Microwave QM1014 User Manual Download | Manualshive

Page: 58 / 81

background image

QM1014 LO Synthesizer Distribution Unit

User Manual

5.6 SYSTem:READstate? [0-5]

This query allows the user to read the parameters of the stored states without changing any internal reg-
isters. The query output is a list of parameters for the selected state. If no state parameter is given, the
returned state is state 0. The list of state parameters contains comma separated values, without spaces,
in the following order:

RF Power State, External Reference Enabled, External Referece Switch Override,

Tune Frequency

. See the respective command definitions for descriptions of each parameter.

Syntax

:

SYST

:

READ

?

Space

0-5

Query

:SYST:READ? 0

This query requests the parameter values of state 0.

Response

: 0,0,0,10.000000

∙

0 = POWEr:RF is set to 0 or OFF. (page 31)

∙

0 = FREQuency:REFerence:EXTernal is set to 0 or Internal. (page 30)

∙

0 = External Reference Switch Override is 0 (switch-controlled).

∙

10.000000 = FREQuency:TUNE is set to 10 GHz. (page 26)

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 0 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

47

«
...
56
57
58
59
60
...
»

Summary of Contents for QM1014


















































































Reviews:

No comments

Related manuals for QM1014

Brand: Art Pages: 1

AF-600 FP Series

Brand: GE Pages: 129

Brand: Emerson Pages: 69

Brand: Siemens Pages: 4

XJ-L Busway System

Brand: Siemens Pages: 6

SIVACON 8PS LR Series

Brand: Siemens Pages: 8

SIVACON 8PS BD2C EESC Series

Brand: Siemens Pages: 6

SIVACON 8PS LD Series

Brand: Siemens Pages: 8

SIVACON S 8PQ Series

Brand: Siemens Pages: 40

Brand: Siemens Pages: 362

Brand: brennenstuhl Pages: 72

3C10220 - Ethernet Power Source Supply

Brand: 3Com Pages: 44

YEWSERIES 80 SDBS (Style S)

Brand: YOKOGAWA Pages: 38

Brand: Tripp Lite Pages: 20

Brand: Tripp Lite Pages: 68

Brand: American DJ Pages: 1

Brand: Keysight Pages: 14

Brand: DRIESCHER Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands