Quonset Microwave QM1014 User Manual Download Page 57 | Manualshive

Page: 57 / 81

background image

QM1014 LO Synthesizer Distribution Unit

User Manual

5.5 SYSTem:LOADstate [0-5]

This command restores a previously saved state from non-volatile memory. In addition to factory default
state 0, there are 5 re-writeable memory locations, specified by choosing an index between 1 and 5.
The restored parameters are the

RF Power State, External Reference Enabled, External Referece Switch

Override, Tune Frequency

. For a detailed description of the parameters saved, see the relevent command

descriptions in this manual. When the SYSTem:LOADstate command is called, these parameters will be
applied to the device.

Syntax

:

SYST

:

LOAD

Space

0-5

?

There are 6 memory locations, numbered 0 through 5. Memory location 0 contains the factory default
settings, while locations 1-5 are user re-writeable using SYSTem:SAVEstate.

Example

:SYST:LOAD 4

This command loads the state 4 parameters from non-volatile memory and applies
them to the device.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 0 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

46

«
...
55
56
57
58
59
...
»

Summary of Contents for QM1014


















































































Reviews:

No comments

Related manuals for QM1014

Brand: Tripp Lite Pages: 3

Brand: Hama Pages: 35

Brand: ABB Pages: 262

Brand: CyberPower Pages: 2

Premium+ RLNK-P915R

Brand: Middle Atlantic Products Pages: 156

Brand: Tripp Lite Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands