background image

FIRST THINGS FIRST

5

CONNECTING THE ANTENNAS

The AM and FM antennas connect to the AM and FM ter

minals

on the system's back panel.They must be hooked up for you to
receive clear reception.

Uncoil the antenna wires and locate the bare ends. Press down
on the tab to open the terminal and insert the wire. Snap the tab
closed. After connecting the antennas, extend them to their full
length and adjust their positioning for better reception.

SYSTEM SETUP

CONNECTING THE WIRES

Each speaker -the two main, -has a designated set of ter

minals

on the back panel of the central unit.

Uncoil the speaker wires and locate the bare ends. Press and
hold down on the tab to open the red terminal, then insert the red
(+) wire. Release hold to close tab. Use the same procedure for
the black (-) wire into black terminal.

WARNING: Be sure to follow these instructions carefully. The
system can be damaged if speakers are improperly connected.

CONNECTING THE MAIN SPEAKERS

The two main speakers should be set between 6 and 10 feet apar

t. Putting the speakers any closer or any

farther apart may result in distorted sound.

The speakers should also form a 45 degree angle to the central listening point in the room, creating a tri-
angle of listening enjoyment.

Sit Back and Listen...

Fine tuning is best per

formed with the remote

control so that adjustments can be made from 
the viewing or listening area.

Summary of Contents for QSR1000

















Reviews: