Quectel UG89 Hardware Design Download Page 77 | Manualshive

Page: 77 / 78

background image

provided the user can reasonably be expected to have the capability to access information in
that form.
This device complies with part 15 of the FCC Rules. Operation is subject to the  following two
conditions:
(1) This  device  may  not cause  harmful interference, and  (2) this  device  must  accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to  part  15  of  the  FCC  Rules.  These  limits  are  designed to  provide  reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be  determined by turning
the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

⚫

Reorient or relocate the receiving antenna.

⚫

Increase the separation between the equipment and receiver.

⚫

Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

⚫

Consult the dealer or an experienced radio/ TV technician for help.

IC Statement

IRSS-GEN
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.

«
...
75
76
77
78
»

Summary of Contents for UG89















































































Reviews:

No comments

Related manuals for UG89

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Magnescale Pages: 3

Brand: iluminize Pages: 2

Brand: Aurora Pages: 2

653 - AE Series

Brand: VAT Pages: 103

Brand: FASAR ELETTRONICA Pages: 2

Brand: ACS Pages: 2

Brand: Litex Pages: 1

Brand: Scanreco Pages: 48

Brand: Daikin Pages: 32

Brand: HM-Funktechnik Pages: 20

Brand: Estyma Pages: 9

Brand: ILLUMINO IGNIS Pages: 15

Brand: PI Pages: 111

Brand: Aurora Scientific Pages: 21

Brand: Clare Controls Pages: 3

Brand: Swegon Pages: 11

Brand: adept technology Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands