Quectel RMU500-EKNM User Manual Download Page 27 | Manualshive

Page: 27 / 31

background image

5G Module Series

RMU500-EKNM_EVB_Kit_User_Guide 26 / 30

Then, the assembly is finished. The assembled EVB kit is shown below.

Figure 23: Assembled EVB Kit

4.2. Turn on the Module

1. Finish the assembling steps above.

2. Insert a (U)SIM card into the (U)SIM card connector on the EVB.

3. Insert the USB cable (Type-C to dual Type-A). Connect the type-C end to the EVB, one Type-A end

to the computer, and the other Type-A end to an auxiliary power supply. The module will be turned on

automatically when the EVB is powered through the USB interface (J301) or the power jack (J101).

4.3. Communication Via USB Interface

1. Power on the module according to the procedure in

Chapter 4.1

2. When the EVB is connected to a PC with the USB Type-C cable through the USB interface, run the

USB driver disk on the PC to install the USB driver. For details about USB driver installation, see

document [1]

. The USB port numbers can be viewed in Device Manager of the PC when the USB

driver is installed, as shown below.

«
...
25
26
27
28
29
...
»

Summary of Contents for RMU500-EKNM
































Reviews:

No comments

Related manuals for RMU500-EKNM

Brand: Ebyte Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands