background image

QUATRO    

Air Technologies Inc. 

 

Normal (Manual) Operation 

Manual operation of the unit is accomplished by using the (Red) ON/OFF POWER button. 

 

Variable Digital 

Speed Control & “AUTOFLOW” 

Speed control is available in all modes of operation (manual & automatic) and is adjusted with the UP & DOWN arrows 
located just under the POWER button. 

 

 

“AUTOFLOW” is an automatic system pressure compensation system.  After setting the minimum speed required to 

properly evacuate your equipment, the controls will automatically increase the motor speed to compensate for the 
increased pressure as a result of filters getting dirty or a system blockage until maximum speed is reached.  After a filter 
change, system will automatically decrease the speed to the original set point. Please verify that you are achieving 
adequate ventilation after a filter change. If not adjust blower speed. 

 

Remote (Automatic) Operation & Remote Status 

The Quatro System

 

is designed to be used with other pieces of equipment that can support remote operation and/or 

remote status monitoring. The connection is made using the AE427 QUATRO Universal Remote Cable. QUATRO has 
some custom remote cables for specific applications. Contact us for more info on available applications and part numbers. 
The Quatro System

 

supports “Closed Contact” & “1-30V AC or DC” remote operation as well as “Remote Status” signals. 

Switching power to control the 

QUATRO System 

system remotely WILL NOT WORK and can damage the 

unit.  

 

Temporary ON Mode 

Allows you to temporarily override your automatic remote control of the system 

to perform a “quick cleaning” of work 

surface. Temporary ON Mode is only available when the Remote/Standby (L5) light is flashing slowly. Use of this mode will 
temporarily BLOCK OR DISENGAGE all other functions. 

 

To initiate: 

-

 

Press POWER (On/Off) 

button to start unit, “System ON” LED will FADE In-Out, unit will start. 

-

 

When you finish using this feature, press POWER (On/Off) again. All other functions will be un-blocked. 

 
 

Operation, Connection & Enabling 

Most systems will come with a custom remote cable to interface between the QUATRO fume extractor an your equipment. 
If a custom cable isn’t available then the AE427 universal remote cable will be provided.  Connect the AE427 remote cable 
in between the Quatro System & the other piece of equipment using only the wires required as per the diagram below.  

 

Summary of Contents for 425L















Reviews: