Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 70 | Manualshive

Page: 70 / 190

Quasonix QSX-RDMS-RM Series Installation And Operation Manual Download Page 70

Rack-Mount RDMS

TM

Telemetry Receiver

55

Quasonix, Inc.

Figure 98: Enter New Rack Alias

4.1.5.9

LCD Backlight Option

The LCD Backlight option, shown in Figure 99, is used to adjust the lighting on the front panel display screens. This
allows the displays to be easily seen no matter what the lighting conditions in the area where the rack is being used.
To change the LCD Backlight value, select LCD Backlight, then press the Enter key on the front panel.

Figure 99: Options Menu, LCD Backlight Selection

A dialog screen displays, as shown in Figure 100, prompting the operator to enter a new LCD Backlight value using
the rack’s front panel numeric keypad. When the new value is entered, press the Enter key on the keypad.

Figure 100: LCD Backlight Value Entry Screen

«
...
68
69
70
71
72
...
»

Summary of Contents for QSX-RDMS-RM Series































































































































































































Reviews:

No comments