Quark-Elec QK-A042T Manual Download

Page: 6 / 14

Quark-elec Manual

https://www.quark-elec.com

6 of 14

2018

V2.0

6. Connecting

The following figure shows connections for the AIS transceiver. The user should take the time to

familiarize themselves with the system elements and their connections prior to attempting installation.

A042T Class B transponder has the following electrical connections



GPS connector

: a TNC female bulkhead connector mounted on the enclosure for external GPS

antenna. Connect external GPS antenna’



9 pins POWER/NMEA connector

: 9-pin coaxial female connector mounted on the enclosure. It

provides power input and NMEA input/output. NMEA 0183 data can be connected with chart

plotters or other NMEA0183 compatible equipment.



VHF connector

: an N-type female bulkhead connector for external VHF antenna. Connect

external VHF antenna



USB

: Type B USB connector for software configuration and information display on PC. Connect

the PC for software configuration and information display

Note:

Please check your wiring very carefully before applying power to the A042T. Failure to wire the

product correctly could result in permanent damage.

Summary of Contents for QK-A042T















Search results

Summary of Contents for QK-A042T

Reviews:

Related manuals for QK-A042T

Brands by name

Popular brands

Quark-Elec QK-A042T, Manual

Search results

Summary of Contents for QK-A042T

Reviews:

Related manuals for QK-A042T

Brands by name

Popular brands