manualshive.com logo in svg

Quark-Elec QK-A034-B, Manual, Page: 13 / 17

Share
Download
Quark-Elec QK-A034-B Manual Download Page 13

 
 

QK-A034-B Manual 

 

V 2.1 

13 of 17 

2020 

 

4. Configuration (via USB) 

The A034-B Configuration tool software can be found on the free CD provided with your product or at 
https://www.quark-elec.com/downloads/configuration-tools/. 
 
The A034-B Windows configuration tool can be used to setup the port routing, sentence filtering, NMEA 
baud rates, and WiFi settings for the A034-B. It can also be used to monitor and send NMEA sentences 
through the USB port. The configuration tool must be used on a windows PC (or a Mac using 
BootCamp or other Windows simulating software) while the A034-B is connected via USB cable. The 
software cannot access the A034-B via WiFi. 
 
The Configuration tool will not function while another program is using the A034-B. Please close down 
all applications using the A034-B when using the configuration tool. 
  

 

Figure 3: Configuration tool connection 

 
Once open, click ‘

Connect

’. 

 

When A034-B is 

connected to a computer (Windows system) and powered up, ‘A034connected’ will be 

shown at the centre of the bottom and the software version shows at the bottom right. Press ‘

Config

’ 

once you have set the Baud rates for the inputs to save them to the A034-B. 
 
Then press the ‘

Disconnect’

 button to safely remove the device from the PC. 

 
Reboot the A034-B to activate the new settings. 

4.1.  Configuring Baud Rates 

NMEA 0183 input baud rates can be setup from dropdown menu.  
The A034-B can work with standard NMEA 0183 devices (4800bps), the high-speed NMEA 0183 
devices (38400bps) and 9600bps can also be chosen. 
 
Default NMEA baud rates are set to the following default settings: 

•

 

Seatalk:4800bps 

•

 

NMEA IN 1: 4800bps

 

•

 

NMEA IN 2: 4800bps

 

•

 

NMEA IN 3: 38400bps

 

 
These can be adjusted as required. 
 

 

 

Figure 4: Setup the baud rate 

Summary of Contents for QK-A034-B


















Reviews:

No comments