Quantum MC300 Prism User Manual Download Page 110

Page: 110 / 140

Appendix A Event Details Listing

MC300 Prism Management Card User’s Guide

Table 15 Information
Events Detail, Tape
Alert Flag

4683

Soft Error

Drive 4 in this frame has rejected the cartridge. A reload is

underway.

4684

Soft Error

Drive 5 in this frame has rejected the cartridge. A reload is

underway.

4685

Soft Error

Drive 6 in this frame has rejected the cartridge. A reload is

underway.

4900

Configuration

Change

This unit has become the stack-master (elevator controller)

4901

Configuration

Change

This unit has changed from stack-master to slave module

4902

Soft Error

The stack-master is no longer polling this unit

Tape

Alert

Flag

E-mail Message
Error Type

Description

Soft Error

Manual or software unload attempted while prevent media

removal on

Soft Error

Cleaning tape encountered during backup or restore

Soft Error

Attempted load of unsupported tape format

Soft Error

Media loaded that is read-only format

Soft Error

The tape cartridge is nearing the end of its calculated life

FSC

Code

E-mail Message
Error Type

Description

Summary of Contents for MC300 Prism













































































































































Search results

Summary of Contents for MC300 Prism

Reviews:

Related manuals for MC300 Prism

Brands by name

Popular brands

Quantum MC300 Prism, User Manual

Search results

Summary of Contents for MC300 Prism

Reviews:

Related manuals for MC300 Prism

Brands by name

Popular brands