background image

2

Before Installing the LTO-3 (Model B) Half-Height Tape Drive

Product Name Quick Start Guide

Before Installing the LTO-3 (Model B) Half-Height Tape Drive

Handling Precautions 

and Installation 

Guidelines

Always observe the following precautions and guidelines when handling and installing 

LTO-3 (Model B) Half-Height Tape Drives:

• Internal, at all times
• Tabletop,  when  removed  from its free-standing enclosure

Preinstallation 

Requirements

Before installing the LTO-3 (Model B) Half-Height Tape Drive, make sure you have: 

• A host bus adapter (HBA) installed and properly configured in the host computer:

• Parallel SCSI HBA for a parallel SCSI drive

Handling Precautions

• Internal drives have exposed components that are 

sensitive to static electricity. To reduce the possibility of 

damage from static discharge, the drives are packaged 

in a protective antistatic bag. Do not remove the drive 

from the antistatic bag until you are ready to install it.

• Wear an ESD-preventive grounding wrist strap or 

observe similar ESD precautions when working with the 

drive. Be sure the wrist strap makes good skin contact. 

Do not remove the wrist strap until you finish working 

with the drive. 

Also, avoid contact between the drive, other equipment, 
and clothing. The wrist strap only protects the 
equipment from ESD voltages on the body; ESD 
voltages on clothing can still cause damage.

• Before removing the drive from the antistatic bag, touch 

a grounded metal surface to discharge any static 

electricity buildup from your body.

• Handle the drive by its sides rather than by the top cover 

to reduce the risk of dropping the drive or damaging it 

during installation.

• Either lay the drive on a nonconductive surface or put it 

back inside the protective antistatic bag to reduce the 

chance of damage from static discharge

Installation Guidelines

• LTO-3 (Model B) Half-Height Tape Drives with the parallel 

SCSI interface are low voltage differential (LVD) SCSI 

devices. Install LVD drives only in LVD environments. Do 

not mix LVD and HVD devices on the same parallel SCSI 

bus. 

• Due to the high speed of the LTO-3 (Model B) Half-

Height Tape Drive, do not connect more than one LTO-3 

(Model B) drive to the same host bus adapter (HBA).

Summary of Contents for LTO-3



















Reviews: