background image

 

Head Office:

 

Engineering:

 

Unit B, Cranmere Court   

Unit 13 Langley Business Court 

Okehampton    Devon  

Worlds End   Newbury 

EX20 1UE    UK 

                  RG20 8RY 

Tel: +44(0) 1844339993                                                 Fax: +44(0)1844339996           

Email: 

sales@quantumcryogenics.com

                       Web Site: 

www.quantumcryogenics.com

   

 

                                                         

 ATEX-DCT150M-W-28.02.20-00003R5 

 

 

 

    

THE DCT150M-W DIGITEMP DIGITAL THERMOMETER  

    FOR TANKS AND TANK CONTAINERS 

 

 

    

INSTRUCTION MANUAL 

 

 

The  DigiTemp  DCT150M-W  is  a  battery  powered  digital  thermometer  for  tanker  and  tank 

containers, which provides reliable, economic and accurate  temperature monitoring for a wide 

range  of  industrial  applications  in  hazardous  process  areas,  where  potentially  explosive 

atmospheres may be present.  The DCT150M-W has a wide temperature operating range from -

50

°

C to +150

°

C and a guaranteed battery life of 6 years with no maintenance. The DCT150M-W 

wireless  thermometer  provides  real  time  updates  of  temperature  readings  to  communication 

gateways  including  satellite  systems  operating  in  the  IEEE  802.15.4  frequency  range.  The 

DigiTemp DCT150M-W is housed in a robust glass reinforced nylon case with a fully integrated 

sealed  polycarbonate  face  which  is  waterproof  to  IP67  and  which  eliminates  surface 

electrochemical  corrosion  problems.  The  DCT150M-W  is  suitable  for  hostile  environments 

without additional protection. 

 

 

iNSTALLATION REQUIREMENTS 

 

Prior to installing this thermometer, these instructions should be fully read. Failure to do so could 

result  in  permanent  damage  to  the  unit.  Particular  attention  should  be  given  to  the  following 

points:- 

 

 

The Near Field Communication function of this device must not be used in a hazardous area 

(safe area use only). 

 

This equipment shall not be exposed to strong electromagnetic fields exceeding 1A/m rms or 

3V/m rms when located in  a hazardous area These values are maximum limits and  may be 

limited further in accordance with the Canadian Electrical Code or the National Electrical Code 

or IEC/EN 60079-14, as well as local requirements (as applicable). 

 

The installer and user must take appropriate measures to avoid accumulation of electrostatic 

charge on the non-conductive enclosure surface. Clean only with a damp cloth. 

 

The  equipment  enclosure  must  be  sufficiently  thermally  isolated  from  hot  or  cold  process 

vessels that its local ambient remains within the specified ambient temperature range. 

 

The equipment must not be allowed to become immersed in dust. 

Summary of Contents for DCT150M-W











Reviews: