background image

2

Before Installing the DAT 320 Tape Drive in Your System

DAT 320 Quick Start Guide

Before Installing the DAT 320 Tape Drive in Your System

Avoiding Electrostatic 

Damage

Your internal tape drive has very sensitive components that are prone to damage from 

electrostatic discharge (ESD). Use extreme care when handling the drive, as it can be 

damaged by ESD.
Before handling the drive, read the ESD instructions that follow to prevent damage to 

the drive.

• Wear an ESD-preventive grounding wrist strap or observe similar ESD precautions 

when working with the drive. Be sure the wrist strap makes good skin contact. Do 

not remove the wrist strap until you finish working with the drive.

• Before you remove the drive from the antistatic bag, touch a metal or grounded 

surface to discharge any static electricity buildup from your body.

• Avoid contact between the drive, other equipment, and clothing. The wrist strap 

only protects the equipment from ESD voltages on the body; ESD voltages on 

clothing can still cause damage. 

• When the drive is not being used, keep it in its antistatic bag.
• Hold the drive by its edges only. Avoid touching any exposed parts on the printed 

circuit board.

• Always place the drive on top of or inside the antistatic bag to reduce the chance of 

ESD damage

Preinstallation 

Requirements

In addition to the contents included with your internal tape drive, you need the 

following items to install your internal tape drive.

• A  USB  2.0  port
• 5.25-inch half-height bay (for internal drive)
• Backup application software that supports the internal tape drive. For a list of the 

latest backup software applications tested with the internal DAT 320 tape drives, 

please visit our Web site at 

http://www.quantum.com/ServiceandSupport/

Index.aspx#

Unpacking and 

Inspecting the Drive

Before you unpack the contents of your drive package, inspect the shipping containers 

for damage. If you spot damage to the container, notify your carrier immediately.
When you unpack the package, compare the items received with those on the packing 

list. If any item is missing or damaged, please contact your place of purchase 

immediately.

Summary of Contents for DAT 320 CD320UE















Reviews: