background image

14 

Duty Cycle 

The Duty Cycle mode is similar to Continuous mode in that a continuous stream of pulses is 
output.  The exception is the outputs are only active for a set number of seconds (

DC:On

 

menu), then disabled for another set time period (

DC:Off

 menu) before being re-enabled.  This 

cycle is repeated for a set number of times (

CYCLES

 menu), after which all outputs cease.  

Setting the number of cycles to zero results in continuous cycling, until the Stop Key is 
pressed. 

The Ext/Gate input may be used as a gate or interlock by setting the 

GATE

 menu to 

Low 

or

 

High

.  Pulses will then only be generated while the external trigger input is active.  Selecting 

Low 

will make the gate active low, while selecting 

High 

will make the gate active high. 

The Run key must be pressed to start the Duty Cycle mode. 

Burst 

Burst mode is similar to Continuous, except only a certain number of pulses will be output 
(

#/BURST

 menu), after which outputs are disabled. 

The Ext/Gate input may be used as a gate or interlock by setting the 

GATE

 menu to 

Low 

or

 

High

.  Pulses will then only be generated while the external trigger input is active.  Selecting 

Low 

will make the gate active low, while selecting 

High 

will make the gate active high. 

The Run key must be pressed to start Burst mode. 

GATE  -  Gate Select 

When not in External Trigger mode, the Ext/Gate input on the 9412/9412A can be used as a 
gate signal.  When the gate is enabled, pulses will only be output while the signal into the 
Ext/Gate input is active -- thus, this signal will act as a safety interlock or external control sig-
nal. 

The Ext/Gate input may be used as a gate or interlock by setting the 

GATE 

menu to 

Low 

or 

High.  

Pulses will then only be generated while the external trigger input is active.  Selecting 

Low 

will make the gate active low, while selecting 

High 

will make the gate active high.  Set-

ting the 

GATE 

menu to 

Off 

will disable the Gate function. 

The setting of the 

GATE 

menu is used to determine when the signal is active.  If the gate 

menu is set (active) 

High

, pulses will only be generated if the Ext/Gate input signal is greater 

than 3.5 Volts.  If set to (active) 

Low,

 outputs will be enabled as long as the Ext/Gate input 

signal is less than 2.0 Volts. 

Summary of Contents for 9412
































Reviews: