Quantum Data 780C User Manual Download Page 136 | Manualshive

Page: 136 / 240

background image

780C Multi-Interface Interoperability Tester

– User Guide

Page 135

September 29, 2014

Revision A1

7.1.2

Connection Configurations for Testing HDBaseT Source Devices

The 780C

’s HDBaseT input port acts as a “reference” HDBaseT sink device. Therefore it enables you to

emulate a known good HDBaseT sink device to conduct diagnostics upstream toward the source device. The
following illustrations show the typical configurations.

7.1.3

Procedures for Testing Upstream (Source Test) with the Installer Utility

Use the following procedures to test the video from an HDMI source device directly at the HDMI source or
through an HDMI repeater device or HDBaseT distribution device. You can view the incoming video and check
the video and timing parameters of the incoming video.

1. Make the physical connection between the 780C

HDMI IN

or HDBaseT IN port and the upstream device

under test using the configuration instructions above or by following the instructions on the screen.

2. Enable the HDMI or HDBaseT as the active digital interface input.

«
...
134
135
136
137
138
...
»

Summary of Contents for 780C

















































































































































































































































Reviews:

No comments

Related manuals for 780C

Brand: LaserLine Pages: 24

Brand: Oceanic Pages: 68

Brand: Oceanic Pages: 24

Brand: OBD Pages: 5

Brand: CONDTROL Pages: 8

Universal Analyzers 275E

Brand: Ametek Pages: 34

Brand: Topcon Pages: 59

Brand: AKCP Pages: 16

Brand: Swann Pages: 106

Brand: Dakota Digital Pages: 34

Brand: Value Pages: 20

Brand: Konica Minolta Pages: 92

Multifunction Compensator

Brand: Halcyon Pages: 20

Brand: AEMC Pages: 4

Brand: International Light Technologies Pages: 19

Digalox DPM72-MPPA

Brand: TDE Instruments Pages: 8

Brand: Haltech Pages: 20

Brand: Amcrest Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands