background image

Model QRJ03H 

Installation, Operation and Maintenance Manual 

 Rev. 

09/19/2011 

QRJ03H-IOM 

3

 
I

NSTALLATION

 

1) 

Place jack assembly on lift rack rails. 

2) 

Once side members are adjusted and jack is centered between the rails, tighten the (4) hex 

bolts (2 per side) to lock in place, Fig 2.   

 

Fig. 2

 

Operation 

Note: 

Before lifting a vehicle, operate the jack through a couple of cycles to become familiar 

with the controls. 

1) 

Roll jack forward before moving vehicle on lift rack. Be sure vehicle is centered on 
rack, apply parking brake and chock wheels. 

2) 

Roll jack(s) to the vehicle manufacturer’s recommended pick-up points. Extend lift 
pad arms to proper lift points. Use lift pad spacers if necessary. 

3) 

Raise jack by pumping the jack handle. 

4) 

Raise vehicle to desired height. 

5) 

Lower jack onto lock. 

6) 

To lower jack completely, raise off of lock and turn the valve handle counter 
clockwise. Push lift pad arms in, remove lift pad spacers (if used). Roll jack forward 
before moving vehicle off rack. 

 

Maintenance 

Daily

:

 Inspect jack and it’s components for damage or excessive wear.  Replace parts as 

required.  See parts list. 

 

Inspect hydraulic system for leaks.   

Annually:

 

Check hydraulic pump fluid level.  When jack is completely lowered remove 

breather plug and check oil level.  Oil should be at top of filler plug hole. 

 

IMPORTANT! 

 

Failure to keep lift free of corrosive agents and solvents will lead to reduced service life, which 
could result in property damage and/or personal injury.  If any problems are encountered, 
contact your local service representative. 

Summary of Contents for QRJ03H







Reviews: