background image

2

S A F E T Y   I N S T R U C T I O N S

IMPORTANT

 

 

Please note when you open the carton 
carefully check the unit and make sure 
there are no damages. If you have any 
problems with the unit, with how the various 
functions work or with hidden damages or 
missing parts please call 1-800-459-4409 
(EST) immediately for service. NOTE: DO 
NOT RETURN UNIT TO THE STORE BEFORE 
CALLING THE TOLL FREE NUMBER. Do 
not dispose of your cartons until you are 
completely satisfied with your new fireplace 
heater. Read all instructions thoroughly be-
fore operating your new Electric Fireplace.

NOTE: Light bulbs may become loose 
during shipping. If the flame effect is dim 
or does not work, please check that light 
bulb or bulbs are finger tight in socket. See 
instructions for replacing bulb or bulbs. 
Please do not return the sample to the store 
before checking light bulbs.

NOTE: The electric fireplace heater may 
emit a slight harmless odor when first 
turned on. This is caused by activating the 
internal heater components for the first time 
and should not occur again. 

1) Read all instructions before using this 
electric fireplace heater.
 

2) This electric fireplace heater is hot when 
in use. To avoid burns, do not let bare skin 
touch hot surfaces. The grill directly in front 
of the heater outlet becomes hot during 
heater operation. Keep combustible materi-
als, such as furniture, pillows, bedding, 
papers, clothes, and curtains at least 3 feet 
(0.9 m) away from the front of the unit and 
keep them away from the sides and rear. 

3) Extreme caution is necessary when any 
heater is used by, or near, children or indi-
viduals with disbalities and whenever the 
fireplace is left operating and unattended. 

4) Always unplug fireplace when not in use.
 
5) Do not operate any electric fireplace with 
a damaged cord or plug or after the heater 
malfunctions, has been dropped or dam-
aged in any manner. 

6) Do not use outdoors. 

7) This electric fireplace heater is not in-
tended for use in bathrooms, laundry areas 
and similar indoor locations. Never locate 
heater where it may fall into a bathtub or 
other water container. 

IMPORTANT SAFETY INSTRUCTIONS  

WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAU-

TIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE 

RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO  

PERSONS, INCLUDING THE FOLLOWING:

Summary of Contents for NDF-QC913











Reviews: