Qualcast SPP41 Instruction Manual Download Page 13

Page: 13 / 14

Tip the machine slightly towards the oil filler pipe and reach under the deck.
Hold the blade and unscrew the blade bolt counterclockwise using a spanner wrench.

Remove the washer and the blade.
Inspect the blade adaptor for any signs of damage.

Fit a new blade, locate the blade on the two studs on the blade

ange and then replace the

washer and bolts.

Check the washer is still slightly domed to keep the pressure on the bolt to stop it

unwinding, keeping the blade firmly secure. Then replace the washer (right way around!)

and bolts.
Make sure the blade is correctly located, and then firmly tighten the bolt. Do not over

tighten. The up turn of the blade must project into the motor compartment.

NOTE:

If you are unsure about performing this operation, call our helpline or go to an

authorised dealer to change the blade for you.
List of consumable parts:

QC12YC

Spark plug

932217

Blade bolt

933918

Collection grass bag

466018

Fixing knob

933206

Blade

Parts can be ordered via www.gardenservicecentre.co.uk.

Troubleshooting

WARNING!

Always switch off the engine and pull the ignition cable before starting any

inspection or adjustment work.
If after making an adjustment or repair to the engine you let it run for a few

minutes, remember that the exhaust and other parts will get hot.

The following table provides solutions to common problems encountered with the lawn
mower:

Fault

Possible cause

Solution

Loud while running,

machine vibrates

heavily

- Screws are loose

- Blade fasteners are loose

- Blade is unbalanced

- Check screws

- Check blade fasteners

- Replace blade

Engine does not

start

- Start/stop bar not pressed

- Primer bulb is empty

- Spark plug is defective

- Fuel tank is empty

- Engine may be flooded

- Press start/stop bar

- Press primer bulb 3-5 times

- Replace spark plug

- Refill with fuel

- Remove plug and dry, see page

Engine runs

unsteadily

- Air filter is soiled

- Spark plug is soiled

- Clean the air filter

- Clean the spark plug

Uneven mowing

results

- Blade is blunt

- Cutting height is too low

- Sharpen the blade

- Set correct height

Unsatisfactory grass

collection

- Cutting height is too low

- Blade is worn

- Grass bag is clogged

- Set correct height

- Replace the blade

- Clear any clogged grass debris

Summary of Contents for SPP41















Search results

Summary of Contents for SPP41

Reviews:

Brands by name

Popular brands

Qualcast SPP41, Instruction Manual

Search results

Summary of Contents for SPP41

Reviews:

Brands by name

Popular brands