background image

  

  

11

10

  

  

Customer Helpline 

0845 034 2279

www.gardenservicecentre.co.uk

Customer Helpline 

0845 034 2279

www.gardenservicecentre.co.uk

Operating the Grass Trimmer

Step 4 - Extending spool line while trimming

1) While the line spool is running at full speed, tap its underside briefly against the ground. 
2) If the spool lines are still not sufficiently extended, tap the underside against the ground again.
3) If the line has already become too short, it will no longer be extended by pressing the 

underside against the ground. You must pull it out from the line spool by hand.
4) Switch off the motor.
5) Lay the machine on the ground.
6) Push by hand on the underside of the line spool and pull both lines out until they are 

somewhat longer than the edge of the protective bonnet. The lines are trimmed to the correct 

length by the line trimming knife.

WARNING!

 Ensure there is mixed fuel in tank with the correct ratio of fuel to oil. Make sure all 

guards and handles are properly and securely attached.

Operating the Grass Trimmer 

Step 2 - Starting the Engine (continued)

5) Use your left hand to hold the appliance firmly by the shaft. (whilst facing the rear of the unit)
6) Pull out the pull cord until you feel resistance. Then pull  vigorously 3 to 4 times. When the 
engine attempts to tick over (the engine has ignited).
7) Set the choke lever to the mid-position (HALF CHOKE  ).
8) Pull the start grip (

D

) again quickly and strongly until the motor runs.

9) After about 30 seconds of warming up and getting up to speed you can operate the machine.

2b Start it in warm engine as following steps

1) Set the switch to (START)                .
2) Set the choke lever to (RUN  ).
3) Pull the starter grip (

D

) quickly until engine runs.

2e Running Throttle Position

Hold the trimmer with the both hands on U type handle. Press and hold the throttle lockout trigger 
(

E

)and  squeeze the throttle trigger (

F

) as required. 

NOTE! 

Keep a firm grip with both hands while in operation. 

NOTE! 

The trimmer should be held in a comfortable position with the rear handle about hip 

height. 

NOTE! 

Always operate trimmer at full throttle.

WARNING!

 Never operate this unit on the operator’s left side.

Step 3 - Trimming

E

F

Stopping

Stopping

Release the throttle trigger(F), and set the switch to STOP             . 

Summary of Contents for GDB30B
















Reviews: