background image

Care and Maintenance:

Your QuadraTop is made of the finest ma

-

terials available but to keep it looking new 
and for the maximum possible wear, it will 
need periodic cleaning and basic mainte-
nance. The main threats to your soft top are 
pollutants, dirt and grime. By keeping your 
soft top clean you will prolong the life of your 
top.
We recommend the following to keep your 
top like new:

Washing: The soft top fabric should be was-
hed often using a mild soap, warm water and 
a soft bristle brush (do not use the brush on 
the window glass!). You can also use special 
soft top cleaners available on our website

.

  

Make sure that after cleaning you rinse with 
clear water to remo-ve all traces of soap.

Zippers: Keeping the zipper cleaned and 
lubricated with a silicone lubrican

t

 

will help 

prevent damage and keep the

 

zippers in a 

smooth working condition. If zipper opens 
behind the slider, the slider may

 

have been 

spread apart. This problem can

 

usually be 

fixed

by using an ordinary pair of pliers to bring 
the sides back into parallel. Return slider to 
the end of the zipper in the nor- mal Open 
position. Squeeze lightly at

First and test zipper. If the zipper continues 

to remain open squeeze more firmly with 

pliers and try the zipper again. Repeat proce-
dure until your zipper operates correctly.

Windows: It is very important that you keep 
your QuadraTop windows clean! Use a mild 
soap and water solution to gently clean your 
windows. NEVER wipe your windows clean 
with a dry cloth! Dust and dirt on a dry cloth 
can scratch your windows causing “fogging” 
and permanent damage. When re- moving 
your windows, store them with a towel be-
tween the panels/rear windows to protect 
them from damage. If frost or ice forms on 
the outside of your windows during the win-
ter, DO NOT use an ice scraper to remove 
this frost. Over time you will see small micro 
scratches in your windows which are natural 
wear and tear. These Micro scratches can be 
“polished” out using window polish (Available 
at Quadratec.com).

Water/Fabric: In the event of seeping 
through the seams, 3M Scotchgard® may 
be applied on the inside of the seams to stop 
the see. Rips in the fabric may be repaired 
with Bondex® iron on patches. Iron the 
patches to the Inside of the top, carefully 
following the Bondex® instructions.

Snaps: Keep snaps cleaned and lubricated 
with silicone to help prevent snaps from 
sticking to the studs. If a snap does beco-
me stuck to a stud, use a screwdriver and 
GENTLY pry apart to prevent permanent 
damage to the snap or the top fabric.

12

Summary of Contents for QuadraTop Adventure Top S With Flip Back...















Reviews: