manualshive.com logo in svg

Quadra-Fire MT VERNON-AE, Troubleshooting Manual, Page: 19 / 29

Share
Download
Quadra-Fire MT VERNON-AE Troubleshooting Manual Download Page 19

MT VERNON-AE TROUBLE SHOOTING MANUAL

7020-057D

9-30-2010

IGNITER TROUBLE-SHOOTING

Wall Control Error Code

SRV7000-462

AC INPUT

HALLS CONVECTION

IGNITER

OPEN TC3

TC2 DROP TUBE THERMOCOUPLE
TC1 FIREPOT THERMOCOUPLE

HALLS COMBUSTION

WALL CONTROL

FUEL LEVEL SENSOR

FEED, AUTOCLEAN, & VACUUM SWITCH

SNAP DISC

15 volt DC INPUT

BATTERY BACKUP

COMBUSTION

BLOWER

HOPPER & DOOR SENSORS

FEED MOTOR

AUTOCLEAN

CONVECTION

BLOWER

Items to check:

Check the igniter(SRV7000-462):

  *Check for continuity in the igniter (should get around 36 

ohms) or apply direct power to it.  (This is an AC component)

Check the AC power supply harness (#7034-220):

  *

Check for power or a broken connection.

Check for power at the igniter harness 

(SRV7034-199):

  *Make sure all connections are good.

  *Check for continuity in the wire harness.

Check for power at the control board (SRV7000-456):

  *Unplug the unit and restart.  Make sure the wall control says 

“Startup”.

  *If power is not present, check the fuse or replace the control 

board.

UPDATE:

  *Igniter chamber update communication was sent out on 

Sept. 18, 2007.  This update will increase the service life of the 

igniter.

Connection point for the 

igniter harness.(#7000-199)

Connection point for the AC power 

supply harness. (#7034-220)

PAGE 19

15 amp fuse #7000-491/10

Summary of Contents for MT VERNON-AE






























Reviews:

No comments