Quadra-Fire 43M-ACC-NZ Installation Manual Download Page 1

Page: 1 / 20

7037-181A

August,

2018

4300 MILLENNIUM

NEW ZEALAND

WOOD APPLIANCE

AUTOMATIC COMBUSTION CONTROL

(ACC)

MODEL:

43M-ACC-NZ

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

NOTICE: DO NOT DISCARD THIS MANUAL

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

WARNING

Hot glass and appliance will cause burns.

• Do not touch glass until it is cooled

• Use leather gloves when reloading fuel

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high

temperatures

• High temperatures may ignite clothing or other

flammable materials.

• Keep clothing, furniture, draperies and other

flammable materials away.

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may over fire and generate poisonous

gases (i.e. carbon monoxide).

•

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

•

Do not over fire - If appliance or chimney connector

glows, you are over firing. Over firing will void your

warranty.

•

Comply with all minimum clearances to combustibles

as specified. Failure to comply may cause house fire.

WARNING

If the information in these instructions

is not followed exactly, a fire could result

causing property damage, personal injury,

or death.

Summary of Contents for 43M-ACC-NZ





















Search results

Summary of Contents for 43M-ACC-NZ

Reviews:

Related manuals for 43M-ACC-NZ

Brands by name

Popular brands

Quadra-Fire 43M-ACC-NZ, Installation Manual

Search results

Summary of Contents for 43M-ACC-NZ

Reviews:

Related manuals for 43M-ACC-NZ

Brands by name

Popular brands