background image

USER MANUAL

 

 

Rigging the Fixture      

 

 

 

 

z

 

The installation of the fixture has to be built and constructed in a way that it 

can hold 10 times the weight for 1 hour without any harming deformation. 

z

 

The installation must always be secured with a secondary safety attachment, 

e.g. an appropriate catch net. This secondary safety attachment must be 

constructed in a way that no part of the installation can fall down if the main 

attachment fails. 

z

 

Make sure the area below the installation place is free from unwanted 

persons during rigging, de-rigging and servicing. 

z

 

The operator has to make sure that safety-relating and machine-technical 

installations are approved by an expert before taking into operation for the 

first time and after changes before taking into operation another time. 

z

 

The operator has to make sure that safety-relating and machine-technical 

installations are approved by a skilled person once a year. 

z

 

The fixture should be installed in the position where persons cannot reach 

and where persons may walk by or be seated. 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION:   Please consider the respective national norms during 

the installation! The installation must only be carried out 
by an authorized employee or dealers! 

CAUTION:      When installing the device, make sure there is no highly 

in inflammable material (decoration articles, etc.) in 
between a distance of min o.5 meter. 

Summary of Contents for 152.740

















Reviews: