background image

8

 

QTech

Spray.com

 

SPECIFIC SAFETY RULES 

 

WARNING: 

Do not use guns for spraying flammable materials. 

 

WARNING: 

Be aware of any hazards presented by the material being sprayed, 

 

and consult the markings on the material container or the information supplied 

by the manufacturer of the material to be sprayed.

 

WARNING: 

Do spray any material where the hazard is not known.

 

WARNING: 

Do not clean guns with flammable solvents with 

 

a flash

-

point below 55

°

C. 

 

NOTE: 

A non

-

flammable solvent is here defined as one which has 

 

a flash point above 55

°

C. 

 

WARNING: 

This appliance cannot be used by children under 18 years old or 

 

persons with reduced physical, sensory or mental capabilities or lack of 

 

experience or knowledge of the safe operation of the applicance. 

 

WARNING: HIGH PRESSURE

 

Never leave pressurized system unattended. Always follow the 

PRESSURE 

 

RELIEF PROCEDURE

. Take precautions to avoid high pressure 

 

component rupture.

 

DANGER: INJECTION INJURY

 

Skin injection by high pressure paint is not a simple cut. It must be treated 

 

surgically immediately.

 

WARNING: FIRE AND EXPLOSION HAZARD

 

Take all precautions to avoid sources of sparks and ignition when spraying. 

 

Keep the machine at least 6 meters away from the spraying operation.

 

WEAR PROTECTIVE EQUIPMENT AT ALL TIMES

 

Always use a respirator, eye protection and protective clothing. Keep clear of 

moving parts when starting or operating the sprayer. Do not put your fingers 

into any openings to avoid amputation by moving parts or burns on hot parts. 

 

When starting the motor, maintain a safe distance from moving parts of the 

equipment. Before adjusting or servicing any mechanical part of the sprayer, 

 

follow the 

PRESSURE RELIEF PROCEDURE

.

 

EXPLOSION RISK FROM HALOGENATED HYDROCARBON SOLVENTS

 

Never use halogenated hydrocarbon solvents in this machine.

 

Contact with aluminum parts may cause an explosion.

 

Some of the most common of these solvents are:

 

Carbon tetrachloride

 

Chlorobenzene

 

Dichloroethane

 

Dichloroethyl Ether

 

Ethyl Bromide

 

Ethyl Chloride

 

Tetrachloroethane 

 

9

 

QTech 

QT830 Airless Sprayer

 

Summary of Contents for QT830



















Reviews: