QTech QSW-4600 Series Hardware Installation And Reference Manual Download

Page: 36 / 58

QSW-4600

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

3 Product Installation

Please ensure that you have carefully read Chapter 2.

Make sure that the requirements set forth in Chapter 2 have been met.

3.1 Installation Flowchart



Mount the switch to the rack



Connect the system grounding



Connect the power supply



Connect interface cables



Bundle the power cables or optical fibers



Installation check

3.2 Confirmations before Installation

Before installation, please confirm the following points:



Whether ventilation requirements are met for the switch



Whether the requirements of temperature and humidity are met for the switch



Whether power cables are already laid out and whether the requirements of electrical current are met



Whether related network adaption lines are already laid out

3.3 Installing the QSW-4600

Precautions

During installation, note the following points:



Connect the power cables of different colors to the corresponding grounding posts.



Ensure that the interface of the power supply cable is well connected to the power interface of the device. The power

cables must be protected using power cable retention clips after they are connected to the device.



Do not place any articles on the QSW-4600 series switch.



Reserve a spacing of at least 10 cm around the chassis for good ventilation. Do not stack the devices.



The switch should be located at places free from the large power radio launch pad, radar launch pad, and

high-frequency large-current devices. If necessary, electromagnetic shielding should be adopted. For example, use

interface cables to shield cables.

Summary of Contents for QSW-4600 Series



























































Search results

Summary of Contents for QSW-4600 Series

Reviews:

Related manuals for QSW-4600 Series

Brands by name

Popular brands

QTech QSW-4600 Series, Hardware Installation And Reference Manual

Search results

Summary of Contents for QSW-4600 Series

Reviews:

Related manuals for QSW-4600 Series

Brands by name

Popular brands