QTAC 85C Owner'S Manual Download Page 20

Page: 20 / 22

Page | 20

TECHNICAL SPECIFICATIONS

85C

Tank & Body

Fully-welded, top-grade Copolymer Polypropylene
MTECH PolyTough

construction

Delivery Hose

3/4 inch x 50 feet industrial grade rubber (standard)

Delivery Nozzle

Brass ball valve shut-off with fully adjustable brass nozzle

Maximum Tank Capacity

85 US gal (321.8 L)

Pump Type

ACE GE660, E-coat, centrifugal pump

(MAX 115 PSI, 110 GPM)

Engine Type

Honda 4-stroke, overhead camshaft, single cylinder

Tank to Pump

2” NPT Gated Tank to Pump

Draft Hose Port

2” Camlock

ADDITIONAL REFERENCES

The following references are included with the shipment of your QTAC:

• ACE GE-660 Instruction Manual

• Honda Owner’s Manual

We recommend that you read these manuals along with this QTAC Owner’s Manual –

the ACE GE-660 and Honda manuals provide additional detail for the pump and pump

engine, respectively.

Summary of Contents for 85C























Search results

Summary of Contents for 85C

Reviews:

Related manuals for 85C

Brands by name

Popular brands

QTAC 85C, Owner'S Manual

Search results

Summary of Contents for 85C

Reviews:

Related manuals for 85C

Brands by name

Popular brands