background image

After machine turns on, press the “DISPLAY” on remote control, all led are closed, press this button again, all led are restored.

1) Timer ON setting:

      Select a desired ON time through the “UP” and “DOWN” buttons.
      When the air conditioner is OFF, press the "TIMER "button of remote control, and select a desired ON time through the
      “UP” and “DOWN” buttons.
      "Preset ON Time" is displayed on the operation panel.
      ON time can be regulated in 1-24 hours.

2) Timer OFF setting:

      When the air conditioner ON, press "TIMER " button of remote control, and select a desired OFF time through the
      “UP” and “DOWN” buttons.
      "Preset OFF Time" is displayed on the operation panel.
      OFF time can be regulated in 1-24 hours

When unit is on, press the “SWING”, the Air Outlet will swing continuously up and down; by pressing this button again the Air 
Outlet will stop and remain in that position.

OPERATION MODES & SETTING

MODE
COOL / DRY

ROOM TEMPERATURE
64°F - 95°F

Make sure exhaust hose is installed correctly.
Power supply outlet meets the requirements.
The outlet is for AC use.

Do not share outlet with other appliances.
Power supply is AC 115V/60Hz.
Fuse specification: T3.15A/250V.

Cooling Mode

Dehumidifying Mode

Fan Mode

Display Setting (Remote control setting)

Timer Setting (Remote control setting)

SWING

Press the "MODE" button till the "    " Cool icon appears.
Press the " UP "or “DOWN "button to select a desired room temperature (61°F -90°F)
Press the "SPEED" button to select fan speed.
Press the" SWING" button to set Air Outlet angle.

Press the " MODE " button till the "    “Dehumidify icon appears.
Press the "DOWN "or UP "button to select a desired room temperature (61°F -90°F)
Press the "SPEED" button to select fan speed.
Press the" SWING" button to set Air Outlet angle.

Press the " MODE " button till the "   " Fan icon appears.
Press the "SPEED" button to select fan speed.
Press the" SWING" button to set Air Outlet angle

Heater Mode

Press the " MODE "button till the "    " Heater icon appears.
Press the "DOWN" or "UP" button to select a desired room temperature (61°F -90°F).
Press the" SPEED" button to select fan speed.
Press the" SWING" button to set Air Outlet angle.

P8

(Under Heater Mode the air conditioner will take few minutes to warm up before fan starts.)

HEAT

(When enter heating mode,the swing will stay at Anti-cold wind angle and can not be controlled)

45°F - 80°F

Summary of Contents for PAC8000-2101












Reviews: