manualshive.com logo in svg

Qlogic SANblade 2300 Series, User Manual, Page: 61 / 108

Share
Download
Qlogic SANblade 2300 Series User Manual Download Page 61

FC2354601-00  A

5-1

Section 5      

Windows NT Driver Installation

(QL2300.SYS)

5.1

Introduction

This section provides instructions for installing the Windows NT driver under the 
following operating system conditions:

■

Initial installation of the Windows NT 4.0 operating system and the 
Windows NT driver

■

Installation of the Windows NT driver in an already installed Windows NT 4.0 
operating system

■

Installing an updated Windows NT driver in an already installed 
Windows NT 4.0 operating system that has an older version of the driver

5.2

Windows NT Driver Files

The latest version of the software drivers and documentation for Windows NT are 
available on the QLogic Web site. Be sure to review the Readme.txt file for both 
new and changed information.

5.3

Windows NT Installation

To install Windows NT 4.0 on a Fibre Channel hard disk attached to a QLA23xx 
HBA, perform the installation procedures in 

section 5.3.1

. If Windows NT 4.0 is 

already loaded on your system, perform the installation procedures in 

section 5.3.2

. 

If Windows NT 4.0 and an older Windows NT driver are already installed on your 
system, perform the update procedures in 

section 5.3.3

.

Summary of Contents for SANblade 2300 Series













































































































Reviews:

No comments