manualshive.com logo in svg

Qlogic iSR6200, Installation Manual, Page: 2 / 218

Share
Download
Qlogic iSR6200 Installation Manual Download Page 2

ii

ISR651101-00  G

iSR6200 Intelligent Storage Router
Installation Guide

Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no 
responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its 
use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications 
described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no 
representation nor warranty that such applications are suitable for the specified use without further testing or 
modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.

Document Revision History

Revision A, March 20, 2009

Revision B, May 24, 2009

Revision C, November 30, 2009

Revision D, May 14, 2010

Revision E, October 29, 2010

Revision F, November 8, 2010

Revision G, September 28, 2011

Changes

Sections Affected

Updated to latest QLogic template, including new 
cover and back graphics.

All

Updated the Tech Support section’s introduction, 
training, and contact information text.

“Technical Support” on page xviii

Added caution about SFP installation.

“Installing the Transceivers” on page 3-6

Added download instructions for the SANsurfer 
Router Manager utility.

“Downloading the SANsurfer Router Manager 
Installer” on page 3-11

Updated the SANsurfer Router Manager installa-
tion instructions for Windows, Linux, and Mac OS.

“Windows Installation” on page 3-13
“Linux Installation” on page 3-13
“Mac OS X Installation” on page 3-13

Updated the procedure for starting SANsurfer on a 
Windows system.

“Starting SANsurfer Router Manager” on 
page 3-14

Removed the references to the obsolete General 
Configuration Wizard and added a reference to 
using the 

iSR6200 Router Manager User’s Guide

 

for information on configuring router ports.

“Configuring the Router” on page 3-14

Updated the link to the firmware Downloads page 
on QLogic.com and enhanced the firmware down-
load procedure.

“Installing New Firmware” on page 3-15

Updated the menu from which the FW Update Wiz-
ard is accessed (was the 

Wizards

 menu; now is 

the 

File

 menu) in SANsurfer Router Manager.

“Using SANsurfer Router Manager to Install Firm-
ware” on page 3-16

Summary of Contents for iSR6200



























































































































































































































Reviews:

No comments