background image

14

15

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO XL-G10.2 / G10.c – Q CELLS

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO XL-G10.2 / G10.c – Q CELLS

14

15

DANGER! Risk of fatal injury due to electric shock!

 

Ä

Block off the installation zone.

 

Ä

Keep children and unauthorized individuals away 
from the solar power system.

DANGER! Risk of fatal injury due to electric shock!

 

Ä

Ensure that modules and tools are not subject to 
moisture or rain at any time during installation.

WARNING! Risk of injury due to falling 
modules!

 

Ä

Secure modules during installation.

 

Ä

Do not install modules in windy or wet weather. 

DANGER! Risk of fatal injury due to electric shock!

 

Ä

Only use dry, insulated tools.

 

Ä

Do not carry out the installation alone.

• 

Only install undamaged modules and 
components.

 

Ä

Do not modify the module (e.g. do not drill any 
additional holes).

3  INSTALLATION

3.2  PREPARATION OF INSTALLATION

confirmation

letter

NOTE! Module damage may occur!

 

Ä

Do not stack modules.

NOTE! Module damage may occur!

 

Ä

Do not install modules near flammable 
gas / vapors.

 

Ä

Do not install modules in close proximity to air 
conditioning systems.

NOTE! Module damage may occur!

 

Ä

Do not drop modules.

NOTE! Module damage may occur!

 

Ä

Only make modifications to the module which have 
been confirmed in writing by Q CELLS.

NOTE! Module damage may occur!

 

Ä

Never lift or move the module with the connection 
cables or junction box.

 

Ä

Carry modules upright and horizontally as 
shown.

NOTE! Module damage may occur!

 

Ä

Never step on modules.

 

Ä

Do not subject modules to any mechanical 
stress.

 

Ä

Do not allow any objects to fall onto modules.

3  INSTALLATION

3.1  SAFETY AND TRANSPORT

Summary of Contents for Q.PEAK DUO XL-G10.c














Reviews: