background image

12

13

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.MAXX-G3 – Q CELLS

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.MAXX-G3 – Q CELLS

12

13

Note! Module damage may occur!

 

Ä

Do not stack modules.

Note! Module damage may occur!

 

Ä

Do not install modules near flammable 
gas / vapors.

 

Ä

Do not install modules in close proximity to air 
conditioning systems.

Note! Module damage may occur!

 

Ä

Do not drop modules.

Note! Module damage may occur!

 

Ä

Only make modifications to the module which 
have been confirmed in writing by Q CELLS.

confirmation
letter

Note! Module damage may occur!

 

Ä

Never lift or move the module with the 
connection cables or junction box.

 

Ä

Carry modules upright and horizontally as 
shown.

Note! Module damage may occur!

 

Ä

Never step on modules.

 

Ä

Do not subject modules to any mechanical 
stress.

 

Ä

Do not allow any objects to fall onto modules

3  INSTALLATION

3.1  SAFETY AND TRANSPORT

Danger! Risk of fatal injury due to electric 
shock!

 

Ä

Block off the installation zone.

 

Ä

Keep children and unauthorized individuals 
away from the solar power system.

Danger! Risk of fatal injury due to electric 
shock!

 

Ä

Ensure that modules and tools are not subject 
to moisture or rain at any time during instal-
lation.

Warning! Risk of injury due to falling 
modules!

 

Ä

Secure modules during installation.

 

Ä

Do not install modules in windy or wet 
weather. 

Danger! Risk of fatal injury due to electric 
shock!

 

Ä

Only use dry, insulated tools.

 

Ä

Do not carry out the installation alone.

• 

Only install undamaged modules and 
components.

 

Ä

Do not modify the module 
(e.g. do not drill any additional holes).

3  INSTALLATION

3.2  PREPARATION OF INSTALLATION

Summary of Contents for Q.ANTUM DUO Z













Reviews: