background image

CABLE/SATELLITE REMOTE CONTROL

The Q Acoustics system has been designed for easy integration into your home entertainment system as it 

has the ability to be controlled by many types of PROGRAMMABLE REMOTE CONTROL. This may include the 

remote control for your SATELLITE and CABLE system if it has PUNCH THROUGH capability. Punch through 

is the common term for being able to programme your remote control to send IR codes to both a TV and an 

AV Preamplifier/Processor. To use punch through you normally select the TV you wish to support first, and 

then the AV Preamplifier/Processor.

The unit uses the PHILIPS RC5 protocol for AV Preamplifiers/Processors. Programming your remote with 

PHILIPS AV codes should allow you to control volume and mute of your unit. In some cases you may also be 

able to control standby and source select with buttons such as              and    . 

Manufacturers often offer several PHILIPS code options for their remote controls. We recommend that you 

work through the PHILIPS code list for your remote and experiment with each one until you find one that 

works well with the unit. It is easiest to recognise when one is working by pressing the volume up/down 

buttons.

We cannot guarantee that the unit will work with your particular remote as the IR codes it sends are outside 

our control, however by supporting the commonly used Philips standard we hope to have made it as easy 

as possible to gain control of your device with the remote control of your choice.

Below we show how two typical programmable remote controls can be set up.

• 

Press the “TV” button (top left of remote).

• 

Point remote away from receiver,

press and hold “ 0”.

• 

The remote’s LED will flash red twice.

• 

Enter “1217”. The remote’s LED will flash

red twice to confirm correct code.

• 

Press and hold “ 1”.

• 

The remote’s LED will flash red twice.

• 

Press TV and

 

your remote controls will now work 

as below:

Button

Function

Vol +

Volume up

Vol -

Volume down

Mute 

(short press)

Mute

       or  Mute 

(long press)

Standby

  

Source select

Instructions

16

TYPE 1 (SATELLITE)

TV

1

+

2

3

6

5

4

7

8

9

0

SELECT

VOL

MUTE

Volume up / down

Mute / Standby

Standby

Source select

Summary of Contents for Media 4





















Reviews: