PRESET STATIONS
YOU CAN STORE UP TO 20 RADIO STATIONS IN THE MEMORY (10 FM/10 AM).
1. SET TO TUNER MODE.
2. TURN TO THE DESIRED RADIO STATION BY “ MANUAL” OR “ AUTO ” TUNING METHOD.
3. PRESS “ MEM/CLK-ADJ ” BUTTON (14) TO ENABLE PROGRAM FUNCTION & “ MEM ” ICON AND PRESET
STATION NR WILL FLASH ON LCD DISPLAY (2)
4. PRESS “ PRE-UP OR PRE-DN ” BUTTON (26,13) TO SELECT THE DESIRED STATION MEMORY FOR
STORAGE.
5. PRESS “ MEM/CLK-ADJ ” BUTTON (14) AGAIN TO CONFIRM THE SETTING.
6. REPEAT STEP 2 TO 5 TO STORE OTHER STATIONS.
7. NOW YOU CAN SELECT THE PRESETS STATIONS IN ORDER BY PRESSING THE “PRE–UP ” BUTTON (26)
OR PRE-DN BUTTON (13).
¾
THE PRE-SET MEMORIES WILL BE CANCELLED COMPLETELY IF DIS-CONNECTING THE MAIN POWER
SUPPLY. YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR
CONVENIENCE USAGE.
¾
THERE ARE 10 SECONDS FOR PROGRAM STATE, AFTER 10 SEC. THIS STATE WOULD RESUME TO
NORMAL TUNER MODE AUTOMATICALLY.
¾
YOU CAN OVERWRITE A PRESENT STATION BY STORING ANOTHER FREQUENCY IN ITS PLACE.
FM & FM-STEREO RECEPTION
z
PRESS THE “ ST/MONO ” BUTTON (8) REPEATEDLY, THE FM PROGRAMS ARE RECEIVING IN MONO AND
STEREO MODE REPEATEDLY. IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS PREFERABLE
TO RECEIVE THE PROGRAM IN MONO.
z
IF STEREO SIGNAL IS BEING RECEIVED, THE STEREO INDICATOR “
” WILL APPEAR ON LCD
DISPLAY (2) TO SHOW FM STEREO PROGRAM IS NOW RECEIVING.
HINTS FOR BEST RECEPTION:
-
-
AM : THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY ROTATE
OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
-
FM : THE RECEIVER HAS A BUILD-IN FM WIRE ANTENNA (36) HANGING AT THE BACK OF THE UNIT. THIS
WIRE SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR THE BEST RECEPTION.
PHONO/AUX
NOTED:
-
REMOVE THE STYLUS PROTECTOR AND PLACE THE CLOTH MATT TO THE PATTER.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM REST BEFORE OPERATING
AND RE-SECURED AGAIN AFTERWARDS.
1. PRESS FUNCTION BUTTON (10) TO SELECT “ PHONO ” MODE.
2. SET THE SPEED SELECTOR (32) TO THE PROPER POSITION DEPENDING ON THE TYPE OF RECORD TO
BE PLAYED.
3. PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR (30) IF REQUIRED).
4. SET THE CUEING LEVER (31) TO THE UP POSITION.
5. LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD
SIDE. THE PLATTER WILL START TO ROTATE AND POSITION THE TONE ARM
OVER THE DESIRED POSITION OF THE RECORD.
6. PULL DOWN THE CUEING LEVER (31). THE TONE ARM WILL COME SLOWLY ON
THE RECORDER AND START PLAYBACK.
7. ADJUST THE VOLUME UP/DOWN BUTTON (3) TO THE DESIRED LEVEL.
8. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT THE TONE ARM
FROM THE RECORD AND RETURN IT TO THE REST POSITION (33).
9. TO STOP INTERMEDIATE, LIFT UP THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST
(33).
REMARK
: AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT
SETTING, SO IT WILL STOP BEFORE THE LAST TRACK FINISH. IN THIS CASE, SELECT
THE AUTO-STOP SWITCH (35) TO “ OFF ”POSITION, THEN IT WILL RUN TO THE END OF
THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN OFF THE UNIT BY POWER
BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH (35) TO “ ON ” POSITION TO STOP
THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION (33).
REMARK : DUE TO PHONO AND AUX DESIGN IN SAME CHANNEL OF THIS UNIT, ONCE THE AUX-IN JACK (37)
PLUGGED BY ANY 3.5MM STEREO PLUG, THE PHONO FUNCTION WILL CHANGE TO AUX IN AUTOMATICALLY
AND THE TURNTABLE WILL STOP TO SPIN. MADE SURE THE AUX-IN JACK (37) WITHOUT PLUGGED BY
ANYTHING BEFORE PLAYING .
E-4
