Pyle View PLRTD155 Manual Download

Page: 1 / 12

《

》

15.4

FLIP-DOWN MONITOR WITH BUILT-IN

DVD,WIRELESS FM MODULATOR & TV

PLRTD155

FEATURES

MONITOR SECTION

HI RES TFT-LCD MONITOR 15.4” WIDE SCREEN

HIGH RESOLUTION : 1280(H) x 800 (V)

BRIGHTNESS : 450 CD/SQ.M

CONTRAST RATIO : 500 : 1

VIEWING ANGLE : 140° (LEFT/RIGHT ) 120° (TOP ) 120°( DOWN )

OVERHEAD CONSOLE WITH TWIN DOME LIGHTS WITH LED

IR TRANSMITTER READY FOR IR WIRELESS HEADPHONE

BUILT-IN OSD DIGITAL FM MODUALTOR

CREDIT CARD SIZE REMOTE CONTROL

ON SCREEN MENU SYSTEM

FRONT PUSHBUTTONS CONTROLS

AUDIO / VIDEO INPUT

MULTI SYSTEM: NTSC & PAL , SECAM AUTO SWITCH ABLE

DVD SECTION

LOT-IN TYPE DVD PLAYER

LAY BACK DISC: DVD-VIDEO, VIDEO –CD, SVCD, CD-DA, CD-RW & MP3

0 BIT DAC VIDEO ENCORDER

00 LINES HORIZONTAL RESOLUTIONS

ROLOGIC DECODER

PEG-2 TWO CHANNEL ANALOG OUT

4-BIT 96KHZ DAC

REQUENCY RESPONSE: 20 Hz to 20KHz

GENERAL SPECIFICATIONS

OWER REQUIREMENT: 12 V DC

BUILT-IN TV TUNER.

SINGLE POWER CABLE WITH NOISE FILTER CIRCUIT

DIN INTERFACE CABLE WITH RCA JACKS FOR AUDIO AND VIDEO

CONNECTIONS

ACCESSORIES

* Overhead Console Mounting Bracket
* Remote Control with Batteries
* Power Connection Cable
* User's Manual

Antenna

Summary of Contents for View PLRTD155













Search results

Summary of Contents for View PLRTD155

Reviews:

Related manuals for View PLRTD155

Brands by name

Popular brands

Pyle View PLRTD155, Manual

Search results

Summary of Contents for View PLRTD155

Reviews:

Related manuals for View PLRTD155

Brands by name

Popular brands