Pyle PLVW65M Owner'S Manual Download Page 9 | Manualshive

Page: 9 / 15

Pyle PLVW65M Owner'S Manual Download Page 9

9

INSTALLATION HARDWARE

(1) ASSY (Rotate combined bracket with Base A..................................................1
(2) Base B................................................................................................................ 1
(3) Plastic tube......................................................................................................... 2
(4) Screw ( 3x10)..................................................................................................... 4
(5) Position clip-screw..............................................................................................1
(6) Clip screw............................................................................................................1

(1)

(2)

(4)

(6)

(3)

(7)

(5)

(8)

(10)

(a)

(b)

(9)

(7) Fastener .............................................................................................................. 1
(8) Fix bolt ................................................................................................................ 1
(9) Tray ..................................................................................................................... 1
(10)sponge (a) ......................................................................................................... 1
(10)sponge (b) ......................................................................................................... 1

«
...
7
8
9
10
11
...
»

Summary of Contents for PLVW65M
















Reviews:

No comments